Cross Bar Linkage Kit, Weber, IDF used
€50.00We’ve made it easy to clean up your throttle linkage act. This kit includes all those hard to locate goodies with one part number. Each Link Pak includes; two cast linkage arms (L/R), one center throttle cable arm, two Hex Shaft support bolts, four heim joints (L/R hand threads), two threaded linkage rods, jam nuts, two centering springs, one barrel clamp, and two steel carburetor linkage arms.
Note: Hex Cross Bars are sold separately if required
all parts available separately from stock as well
XRP, Compression Hose fitting, 3847 XRP – #6 Non-Swivel Hose End
€17.50FUEL LINEÂ RE-USABLE FITTING -BRAIDED HOSE
XRP, compression hose fitting, 3850 XRP – #6 Double Swivel Hose
€38.623850 XRP – #6 Double Swivel Hose End – 45 Degree
Oil system, fuel system , hose end fittings
Easy to fit
NETT
XRP, Compression Hose Fitting, 3853 XRP – #6 Double Swivel Hose
€38.623853 XRP – #6 Double Swivel Hose End – 90 Degree
Suitable oil & Fuel systems for braided hose ends
Easy Fit reuseable
Screwdriver, special, Stubby, 0.8 X 4.0 mm
€9.55This QUALITY screwdriver will allow you adjust your WEBER in a tight space, more than this you can cut the handle to make it even shorter & get into those difficult places
The tip is perfect for adjusting idle & air volume screws
Has flats on the handle so you can count the turns
Carry one at all times if you own a WEBER SOLEX or other similar carburetor
WEBER Special tip 4mm X 0.8 mm
Screwdriver, special, Stubby
€7.76This QUALITY STUBBY screwdriver will allow you adjust your WEBER in a tight space, more than this you can cut the handle to make it even shorter & get into those difficult places
The tip is perfect for adjusting idle & air volume screws
Carry one at all times if you own a WEBER SOLEX or other similar carburetor
WEBER Special tip w 6.25 X 1.2 mm 25 mm
Under Vw /Porsche Tools -see Loads of useful tools focused on the VW/Porsche & all their systems including Weber & carburetor tuning & precision engineering
Adaptor, Weber IDF A/N
€20.33Avoid Fuel Fires–Now you can easily run A/N fittings and stainless steel hoses directly to your Weber IDF or IDA carburetor(s). Simply un-thread the old brass fitting and replace it with the new Weber IDF or IDA A/N Hose Adapter.
This is the quickest and best way to adapt -6 A/N fittings to any Weber IDF or IDA setup. Get yours now.
Note: Works only on Weber IDF or IDA Carburetors w/threaded fuel inlet.
Ideal when installing braided fuel hose–the professional way to do this job
Rebuild Kit ,Weber IDF Carburetor (40, 44, & 48)
€45.00These Weber Carburetor Rebuild Kits are exactly what you need to restore your Weber Carburetors to their original performance potential. All of our kits come with everything you need, including Gaskets, Pump Diaphragms, and O-Rings. (Rebuilds One Carburetor)
also called Tune-UP KIT
NOTE: Floats not included in rebuild kits.
Adapter, Flow meter, to Fit 6534
€16.18The STE Flow Meter allows you to quickly dial in multiple carburetors or throttle bodies. It provides an exact, readable indication of airflow through the carburetors or throttle bodies. The sensitivity and accuracy of the STE Flow Meter is much greater than any other type of synchro tool or gauge. STE Flow Meters can be used to check the air flow at low and high RPM on down draft and side draft engines.
The BK Model is suitable for all intake diameter with approximately 2 inches (48 to 53mm Diameter) without adapter.
The SK Model is ideal for all ram pipes and intake bores of 1 5/8 to 2 1/8 inches (40 to 55mm Diameter).
Screwdriver, special, Stubby
€7.72This QUALITY screwdriver will allow you adjust your WEBER in a tight space, more than this you can cut the handle to make it even shorter & get into those difficult places
The tip is perfect for adjusting idle & air volume screws
Has flats on the handle so you can count the turns
Carry one at all times if you own a WEBER SOLEX or other similar carburetor
With 5.5 mm tip
